How To Install A Safety First Grow And Go

Safety 1st Grow and Go Car Seat Instructions

Safe First has developed a motorcar seat that is versatile, prophylactic and very easy to install. It can be installed in less than 5 minutes and is compatible with all car models. Perhaps its most popular car seat, the Condom 1st Abound and Become, deserves every parent'south attention.

The Condom 1st Grow and Go 3-in-one Car Seat has a lot of neat features: it offers a luxurious, comfy ride for children, has machine-washable covers and is one of the lightest seats in the marketplace.

Here'due south all you need to know earlier you get yours.

Safety 1st Grow and Go Installation Instructions

Rubber 1st Grow and Get rear facing installation

one
Place the car seat at a 45-degree angle so that your baby's head is in line with their spine.
two
Thread the LATCH belt through the rear-facing belt path.
3
Affix the LATCH hook to your automobile's lower ballast points.
4
To tighten the LATCH chugalug, press downward firmly on the car seat. Then, pull the strap to tighten it and make sure your kid is secured.
5
Turn the seat base in a circle, as if you're steering a car, to ensure that it'south installed securely.
6
Guidelines for Rear-Facing Kid Seat

Head Position: The height of your child's caput must exist at least 1 in. (2.5 cm) below the top of the car seat's headrest.
Harness Strap Position: The harness strap must be at or slightly beneath your child's shoulders; never above.
Buckle Position: The buckle must be utilized in either the 1st or 2nd buckle slot. Make use of the buckle nearest to your kid. It should non exist behind or underneath your child.

Watch this short video to learn more.

Safety 1st Go and Abound front end facing installation

ane
Position your car seat in the eye of the backseat and brand sure information technology'southward equally shut to the seatback as possible.
ii
Attach the tiptop tether to the top tether ballast, and arrange it then that information technology is loose.
3
Thread the LATCH chugalug through the back chugalug path, starting from behind.
4
Affix the LATCH hooks to the lower anchor points 0f your vehicle.
v
Pull the LATCH belt and press down firmly on the seat.
6
Tighten up the tether.
vii
Plough the seat base in a circumvolve, as if yous're steering a machine, to ensure that it's installed securely.
viii
Guidelines for forepart facing kid seat:

Head Position: The car seat headrest should not exist placed higher than the top of the child's ears.
Harness Strap Position: The harness should be placed at or above the child's shoulders; information technology should never below.
Buckle Position: The buckle can be used in whatever buckle slot. The buckle should not exist underneath or behind your child.
Choose the slot closest to your child.

Scout this brusque video to acquire more than.

Safety 1st Grow and Go harness straps installation

1
Pull out and push button back the recline handle to extend your kid'southward comfort while putting the child seat into a rear-facing position.
2
Insert the buckle'south metal retainer into the slot that is closest to the child.
iii
Achieve under your seat and betwixt the base of operations and the vanquish of your car, and so through the recline handle.
4
Pull up on the buckle to brand sure it is deeply attached.
5
Accommodate the headrest to its highest position.
vi
Remove fasteners on seat pad and take the headrest pad from the lesser side of the headrest.

Sentinel this brusk video to learn more.

Safety 1st Grow and Go installation with vehicle seat belt

Whether yous're an expert in child restraint systems or are just looking to make certain your little ones are prophylactic and secure, these steps will help you lock a child restraint with the vehicle belt.

1
Review your Vehicle Possessor'southward Transmission! Your vehicle'due south possessor's manual will allow you know if a child restraint can be installed in your vehicle.
2
Determine how the child restraint will be locked in place to prevent distraction or injury.
three
Check the seat's retractor. Depending on your vehicle in that location will at least one of these settings:

Switchable Retractor
Automatic Locking Retractor
Emergency Locking Retractor

4
Check the latch* plates. The latch plates are the portion of the seat belt that inserts into the buckle.

Watch this curt video to larn more.

Lower Anchors and Tethers for Children (LATCH) is a comprehensive system for fitting automobile seats without the use of vehicle seat belts. It's a simple solution to the problem of installing auto seats in vehicles.

Rubber 1st Grow and Get installation with tether

Stride-by-step instructions

1
Take lower anchor belt off.
two
Route the ballast belt and so that it passes through the rear-facing belt path.
3
Pull the lesser anchor belt across to the opposing side.
4
Tilt back the kid restraint.
5
Place child restraint in the rear facing position in the back seat of your vehicle.
half dozen
Affix lower anchor hooks to your car's lower anchors'
7
Firmly push child restraint down and dorsum towards the vehicle seat. The harness straps should exist snug, but not likewise tight. If the harness is besides tight, pull information technology away from your child's body until yous hear a click or feel the belt tighten.
8
Adjusting Tether Strap:

To tighten: Afterward you have locked into place the motorcar seat with the lower anchor belt, push down on the auto seat and gently pull on the free end of the tether strap.

9
To loosen: Lift upwardly on the tether adjuster and button information technology towards the tether hook.

Watch this brusque video to learn more.

Condom 1st Grow & Go installation on airplane

This seat is certified for aircraft use when utilized with the internal harness.
For rear facing shipping installation refer to Rubber 1st Grow and Get rear facing installation.
For rear facing shipping installation refer to Safety 1st Grow and Become rear facing installation.
Install the child restraint in a window seat to avoid blocking the aisle. If the aircraft lap belt is besides short, ask the flight bellboy for a belt extender.

Watch this short video to learn more.

Condom 1st Grow and Go Cleaning Instructions

Cleaning and Washing the Cover

The straps of the Safety 1st Grow and Go can exist done. To remove the convertible car seat comprehend for washing, follow these steps:

1
Heighten the adjustable headrest.
2
Remove the elastic hooks from the plastic clips located around the car seat.
3
Remove the seat pad.
iv
Loosen the elastic straps on the backside of the car seat.
5
Remove the elastic straps from the plastic hooks located beneath the headrests.
6
Remove the headrest cover.
seven
Remove the auto seat's covers.

Things to recollect when cleaning your automobile seat cover:

1
Machine wash separately with cold water.
two
Brand sure harness is closed so fastening strips aren't exposed.
iii
Practise not use bleach.
4
Tumble dry out merely for 10-12 minutes on low heat.
5
Remove immediately to forbid deterioration.

Scout this short video to learn more.

Safety 1st Grow and Go Adjustment Instructions

How to arrange the straps on the Safety 1st Grow and Become

1
Push down on the metallic adjuster beneath the seat pad.
2
Pull on the harness straps to loosen the harness.
iii
Hinge the QuickFit handles inwardly.
4
Raise the headrest to preferred position.

Sentinel this short video to learn more.

Condom 1st Abound and Go how to remove cover

ane
Elevate the adjustable headrest.
2
Take off the elastic hooks positioned around the car seat.
3
Remove the seat pad.
iv
Remove the elastic straps from the plastic hooks positioned below the headrest.
5
Remove the headrest cover.
6
Have off the seat covers from the side of the motorcar seat.

Watch this short video to learn more than.

Safety 1st Grow and Become how to recline

Do non install your child'southward auto seat when it is on an incline, or you lot will run a risk a serious injury. Always make sure that your vehicle is on level/flat ground before installing and testing the recline angle. If your vehicle seat is deep and sloped, identify a towel or foam noodle at the betoken where the seat absorber meets the back of the seat.

Sentry this brusque video to learn more.

How to loosen harness Safety 1st Abound and Become

1
Pull the recline handle out and push the acme of child restraint toward the back.
two
Insert the buckle's retainer into the slot nearest to your child for a snug fit.
3
Pull the metal retainer entirely through the trounce and pad.
four
Pull up on buckle to ensure it is secured and cannot pull out.
5
Suit headrest to its tiptop virtually position.
half-dozen
Pull harness straps through slots on side of headrest.
7
Loosen harness straps.